Mastering Plumbing Fundamentals for Installing a Bathtub
Mastering Plumbing Fundamentals for Installing a Bathtub
Blog Article
Each person may have their personal rationale involving How to Install a Bathtub.
Setting up a bathtub isn't precisely brain surgery, but it does need solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a new one is likewise a moderately hard task. If the old tub is conveniently available, the project can relocate rapidly; if you have to open a wall surface to eliminate the old tub and also place the brand-new tub, the job is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly require an assistant to move out the old bathtub and embeded in the new one. Ensure you have qualified on your own for the task and also fit trying it. Rather than employing a professional to take control of a halfway-completed job, it is much better to think about using one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you set up a brand-new tub in your washroom if you have currently acquired a brand-new bathtub and do not need to change the plan of your previous water system pipes.
Your tools and also material list should make up the following:
Preparing for the Installation
To start with, the sustaining framework provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to prevent pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited accessibility that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will originate from the pipes. Once the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To set up taps, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water as well as check all joints as well as new pipework for leaks and tighten them if required. Load the bathtub and likewise inspect the overflow outlet as well as the regular outlet for leaks.
Finally, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub needs to wait till the tub has been used at least once as this will resolve it into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Safeguard the faucet in position with the producer offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, creating the water to permeate the wall surface between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can break relatively very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly readily available on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that content about How to Install a Bathtub Yourself while looking around the web. Enjoyed our piece of writing? Please share it. Help someone else discover it. Thanks a bunch for your time. Don't hesitate to come by our website back soon.
Emergency? Call us! Report this page